espressif/esp-ui - 0.2.1 - Example esp_idf/esp_ui_phone_s3_lcd_ev

# ESP32-S3-LCD-EV-Board Running ESP-UI Phone Example [中文版本](./README_CN.md) This example demonstrates how to run the ESP-UI Phone on the [ESP32-S3-LCD-EV-Board](https://docs.espressif.com/projects/esp-dev-kits/en/latest/esp32s3/esp32-s3-lcd-ev-board/index.html) with `480 x 480` and `800 x 480` resolution UI stylesheets. ## Getting Started ### Hardware Requirements * An ESP32-S3-LCD-EV-Board with a `480 x 480` or `800 x 480` resolution LCD screen. ### ESP-IDF Required - This example supports IDF release/v5.3 and later branches. By default, it runs on IDF release/v5.3. - Please follow the [ESP-IDF Programming Guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html) to set up the development environment. **We highly recommend** you [Build Your First Project](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html#build-your-first-project) to get familiar with ESP-IDF and make sure the environment is set up correctly. ### Get the esp-ui Repository To start from the examples in esp-ui, clone the repository to the local PC by running the following commands in the terminal: ``` git clone --recursive https://github.com/espressif/esp-ui.git ``` ### Configuration Run `idf.py menuconfig` and modify the esp-ui configuration. ## How to Use the Example ### Build and Flash the Example Build the project and flash it to the board, then run monitor tool to view serial output (replace `PORT` with your board's serial port name): ```c idf.py -p PORT flash monitor ``` To exit the serial monitor, type `Ctrl-]`. See the [ESP-IDF Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects. ### Example Output - The complete log is as follows: ```bash I (27) boot: ESP-IDF v5.1.4-605-g5c57dfe949 2nd stage bootloader I (27) boot: compile time Aug 9 2024 15:34:23 I (27) boot: Multicore bootloader I (27) boot: chip revision: v0.2 I (27) qio_mode: Enabling QIO for flash chip GD I (27) boot.esp32s3: Boot SPI Speed : 80MHz I (28) boot.esp32s3: SPI Mode : QIO I (28) boot.esp32s3: SPI Flash Size : 16MB I (28) boot: Enabling RNG early entropy source... I (29) boot: Partition Table: I (29) boot: ## Label Usage Type ST Offset Length I (29) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (30) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (30) boot: 2 factory factory app 00 00 00010000 00400000 I (30) boot: End of partition table I (31) esp_image: segment 0: paddr=00010020 vaddr=3c080020 size=2a4850h (2771024) map I (451) esp_image: segment 1: paddr=002b4878 vaddr=3fc98e00 size=031a4h ( 12708) load I (454) esp_image: segment 2: paddr=002b7a24 vaddr=40374000 size=085f4h ( 34292) load I (461) esp_image: segment 3: paddr=002c0020 vaddr=42000020 size=732dch (471772) map I (533) esp_image: segment 4: paddr=00333304 vaddr=4037c5f4 size=0c774h ( 51060) load I (551) boot: Loaded app from partition at offset 0x10000 I (551) boot: Disabling RNG early entropy source... I (552) cpu_start: Multicore app I (552) octal_psram: vendor id : 0x0d (AP) I (552) octal_psram: dev id : 0x03 (generation 4) I (553) octal_psram: density : 0x05 (128 Mbit) I (553) octal_psram: good-die : 0x01 (Pass) I (553) octal_psram: Latency : 0x01 (Fixed) I (553) octal_psram: VCC : 0x00 (1.8V) I (554) octal_psram: SRF : 0x01 (Fast Refresh) I (554) octal_psram: BurstType : 0x01 (Hybrid Wrap) I (554) octal_psram: BurstLen : 0x01 (32 Byte) I (555) octal_psram: Readlatency : 0x02 (10 cycles@Fixed) I (555) octal_psram: DriveStrength: 0x00 (1/1) I (556) MSPI Timing: PSRAM timing tuning index: 5 I (556) esp_psram: Found 16MB PSRAM device I (556) esp_psram: Speed: 80MHz I (597) mmu_psram: Instructions copied and mapped to SPIRAM I (800) mmu_psram: Read only data copied and mapped to SPIRAM I (800) cpu_start: Pro cpu up. I (800) cpu_start: Starting app cpu, entry point is 0x40375764 0x40375764: call_start_cpu1 at /home/lzw/esp/work/esp-idf-github/components/esp_system/port/cpu_start.c:159 I (0) cpu_start: App cpu up. I (1462) esp_psram: SPI SRAM memory test OK I (1471) cpu_start: Pro cpu start user code I (1471) cpu_start: cpu freq: 240000000 Hz I (1471) cpu_start: Application information: I (1471) cpu_start: Project name: esp_ui_phone_s3_lcd_ev_board I (1472) cpu_start: App version: 7d4f9ae-dirty I (1472) cpu_start: Compile time: Aug 9 2024 15:34:15 I (1472) cpu_start: ELF file SHA256: 9cb90bd6afc1f054... I (1473) cpu_start: ESP-IDF: v5.1.4-605-g5c57dfe949 I (1473) cpu_start: Min chip rev: v0.0 I (1473) cpu_start: Max chip rev: v0.99 I (1474) cpu_start: Chip rev: v0.2 I (1474) heap_init: Initializing. RAM available for dynamic allocation: I (1474) heap_init: At 3FC9D248 len 0004C4C8 (305 KiB): DRAM I (1475) heap_init: At 3FCE9710 len 00005724 (21 KiB): STACK/DRAM I (1475) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM I (1476) heap_init: At 600FE010 len 00001FD8 (7 KiB): RTCRAM I (1476) esp_psram: Adding pool of 13120K of PSRAM memory to heap allocator I (1477) spi_flash: detected chip: gd I (1477) spi_flash: flash io: qio I (1477) sleep: Configure to isolate all GPIO pins in sleep state I (1477) sleep: Enable automatic switching of GPIO sleep configuration I (1478) app_start: Starting scheduler on CPU0 I (1478) app_start: Starting scheduler on CPU1 I (1478) main_task: Started on CPU0 I (1479) esp_psram: Reserving pool of 32K of internal memory for DMA/internal allocations I (1479) main_task: Calling app_main() I (1479) bsp_probe: Detect module with 16MB PSRAM I (1480) bsp_probe: Detect sub_board2 with 480x480 LCD (GC9503), Touch (FT5x06) I (1480) gpio: GPIO[3]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 I (1481) bsp_sub_board: Install panel IO I (1481) lcd_panel.io.3wire_spi: Panel IO create success, version: 1.0.1 I (1482) bsp_sub_board: Initialize RGB panel W (3091) lcd_panel.io.3wire_spi: Delete but keep CS line inactive I (3118) gc9503: LCD panel create success, version: 3.0.1 I (3121) bsp_lvgl_port: Create LVGL task I (3121) bsp_lvgl_port: Starting LVGL task I (3141) app_main: Display ESP UI phone demo I (3182) esp-ui: [esp_ui_core.cpp:150](beginCore)Library version: 0.1.0 I (3320) app_main: Biggest / Free / Total SRAM : [ 225280 / 317739 / 408515] PSRAM : [12320768 / 12509956 / 13434880] ``` - The following animations show the example running on different development boards. <img src="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_480_480.gif" alt ="esp_ui_phone_s3_lcd_ev_board_480_480"> ESP32-S3-LCD-EV-Board (with a 480 x 480 resolution LCD screen) (<a href="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_480_480.mp4">Click to view the video</a>) <img src="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_800_480.gif" alt ="esp_ui_phone_s3_lcd_ev_board_800_480"> ESP32-S3-LCD-EV-Board-2 (with a 800 x 480 resolution LCD screen) (<a href="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_800_480.mp4">Click to view the video</a>) ## Technical Support and Feedback Please use the following feedback channels: - For technical queries, go to the [esp32.com](https://esp32.com/viewforum.php?f=22) forum. - For a feature request or bug report, create a [GitHub issue](https://github.com/espressif/esp-ui/issues). We will get back to you as soon as possible.

esp_idf/esp_ui_phone_s3_lcd_ev_board