espressif/esp-brookesia - 0.5.0 - Example phone_m5stace_core

# M5Stack CoreS3 Running ESP-Brookesia Phone Example [中文版本](./README_CN.md) This example demonstrates how to run the ESP-Brookesia Phone on the [M5Stack CoreS3](https://docs.m5stack.com/en/core/CoreS3) with `320 x 240` resolution UI stylesheet. ## Getting Started ### Hardware Requirements * An M5Stack CoreS3. ### ESP-IDF Required - This example supports IDF release/v5.1 and later branches. By default, it runs on IDF release/v5.1. - Please follow the [ESP-IDF Programming Guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html) to set up the development environment. **We highly recommend** you [Build Your First Project](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/get-started/index.html#build-your-first-project) to get familiar with ESP-IDF and make sure the environment is set up correctly. ### Get the esp-brookesia Repository To start from the examples in esp-brookesia, clone the repository to the local PC by running the following commands in the terminal: ``` git clone --recursive https://github.com/espressif/esp-brookesia.git ``` ### Configuration Run `idf.py menuconfig` and modify the esp-brookesia configuration. ## How to Use the Example ### Build and Flash the Example Build the project and flash it to the board, then run monitor tool to view serial output (replace `PORT` with your board's serial port name): ```c idf.py -p PORT flash monitor ``` To exit the serial monitor, type `Ctrl-]`. See the [ESP-IDF Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects. ### Example Output - The complete log is as follows: ```bash I (24) boot: ESP-IDF v5.5-dev-3644-g28ac0243bb 2nd stage bootloader I (25) boot: compile time May 30 2025 15:32:07 I (25) boot: Multicore bootloader I (25) boot: chip revision: v0.1 I (25) boot: efuse block revision: v1.2 I (26) qio_mode: Enabling default flash chip QIO I (26) boot.esp32s3: Boot SPI Speed : 80MHz I (26) boot.esp32s3: SPI Mode : QIO I (26) boot.esp32s3: SPI Flash Size : 16MB I (26) boot: Enabling RNG early entropy source... I (27) boot: Partition Table: I (27) boot: ## Label Usage Type ST Offset Length I (27) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (28) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (28) boot: 2 factory factory app 00 00 00010000 00400000 I (29) boot: End of partition table I (29) esp_image: segment 0: paddr=00010020 vaddr=3c080020 size=1c50d4h (1855700) map I (305) esp_image: segment 1: paddr=001d50fc vaddr=3fca5c00 size=02cech ( 11500) load I (307) esp_image: segment 2: paddr=001d7df0 vaddr=40374000 size=08228h ( 33320) load I (314) esp_image: segment 3: paddr=001e0020 vaddr=42000020 size=74a9ch (477852) map I (385) esp_image: segment 4: paddr=00254ac4 vaddr=4037c228 size=19978h (104824) load I (406) esp_image: segment 5: paddr=0026e444 vaddr=600fe000 size=00020h ( 32) load I (418) boot: Loaded app from partition at offset 0x10000 I (418) boot: Disabling RNG early entropy source... I (419) esp_psram: Found 8MB PSRAM device I (419) esp_psram: Speed: 80MHz I (635) mmu_psram: Read only data copied and mapped to SPIRAM I (695) mmu_psram: Instructions copied and mapped to SPIRAM I (696) cpu_start: Multicore app I (1348) esp_psram: SPI SRAM memory test OK I (1357) cpu_start: Pro cpu start user code I (1357) cpu_start: cpu freq: 240000000 Hz I (1357) app_init: Application information: I (1357) app_init: Project name: phone_m5stack_core_s3 I (1357) app_init: App version: v0.4.2-17-g59514c4-dirty I (1357) app_init: Compile time: May 30 2025 15:31:54 I (1358) app_init: ELF file SHA256: d80f1b9ea... --- Warning: Checksum mismatch between flashed and built applications. Checksum of built application is ef79260e6f5202cec75e5416bbccb5e965cc5013ec6f35442ce4726db0c74a34 I (1358) app_init: ESP-IDF: v5.5-dev-3644-g28ac0243bb I (1358) efuse_init: Min chip rev: v0.0 I (1359) efuse_init: Max chip rev: v0.99 I (1359) efuse_init: Chip rev: v0.1 I (1359) heap_init: Initializing. RAM available for dynamic allocation: I (1359) heap_init: At 3FCA9768 len 0003FFA8 (255 KiB): RAM I (1360) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM I (1360) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM I (1360) heap_init: At 600FE020 len 00001FC8 (7 KiB): RTCRAM I (1361) esp_psram: Adding pool of 5824K of PSRAM memory to heap allocator I (1361) esp_psram: Adding pool of 43K of PSRAM memory gap generated due to end address alignment of drom to the heap allocator I (1362) spi_flash: detected chip: generic I (1362) spi_flash: flash io: qio I (1363) sleep_gpio: Configure to isolate all GPIO pins in sleep state I (1363) sleep_gpio: Enable automatic switching of GPIO sleep configuration I (1364) main_task: Started on CPU0 I (1365) esp_psram: Reserving pool of 32K of internal memory for DMA/internal allocations I (1365) main_task: Calling app_main() I (1366) LVGL: Starting LVGL task W (1366) i2c.master: Please check pull-up resistances whether be connected properly. Otherwise unexpected behavior would happen. For more detailed information, please read docs I (1522) M5Stack: Setting LCD backlight: 100% I (1523) app_main: Display ESP-Brookesia phone demo I (1523) app_main: Using stylesheet (320x240 Drak) [I][Brookesia][esp_brookesia_core.cpp:0213](beginCore): Library version: 0.5.0 I (1658) app_main: Biggest / Free / Total SRAM : [ 110592 / 186035 / 358035] PSRAM : [ 5898240 / 6003976 / 6008588] ``` - The following animations show the example running on the development board. <p align="center"> <img src="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_m5stace_core_s3.gif" alt ="phone_m5stace_core_s3" width="400"> </p> <p align="center"> (<a href="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_m5stace_core_s3.mp4">Click to view the video</a>) </p> ## Technical Support and Feedback Please use the following feedback channels: - For technical queries, go to the [esp32.com](https://esp32.com/viewforum.php?f=22) forum. - For a feature request or bug report, create a [GitHub issue](https://github.com/espressif/esp-brookesia/issues). We will get back to you as soon as possible.