espressif/esp_video - 1.0.0 - Example uvc • ESP Component Registry

# USB Video Class Example (See the [README.md](../README.md) file in the upper level [examples](../) directory for more information about examples.) This example demonstrates the following: - How to initialize esp_video with specific parameters - How to open camera interface video device and capture video stream from this device - How to open H.264 or JPEG video device and encode video stream by this device - How to initialize USB video class and see video on the PC ## How to use example ### Software Required * `potplay` APP for PC on Windows OS ### Configure the Project Please refer to the example video initialization configuration [document](../common_components/example_video_common/README.md) for more details about the board-level configuration, including the camera sensor interface, GPIO pins, clock frequency, and so on. Select and configure camera sensor based on development kit: #### MIPI-CSI Development Kit ``` Component config ---> Espressif Camera Sensors Configurations ---> [*] SC2336 ----> Default format select for MIPI (RAW8 1280x720 30fps, MIPI 2lane 24M input) ---> (X) RAW8 1280x720 30fps, MIPI 2lane 24M input USB Device UVC ---> USB Cam1 Config ---> UVC Default Resolution (HD 1280x720) ---> (X) HD 1280x720 (30) Frame Rate (FPS) (1280) Cam1 Frame Width (720) Cam1 Frame Height ``` #### DVP Development Kit ``` Component config ---> Espressif Camera Sensors Configurations ---> [*] OV2640 ---> Default format select (RGB565 640x480 6fps, DVP 8bit 20M input) ---> (X) RGB565 640x480 6fps, DVP 8bit 20M input USB Device UVC ---> USB Cam1 Config ---> Default Resolution (VGA 640x480) ---> (X) VGA 640x480 (6) Frame Rate (FPS) (640) Cam1 Frame Width (480) Cam1 Frame Height ``` #### Select USB video class output video format ##### JPEG ``` component config ---> USB Device UVC ---> USB Cam1 Config ---> Cam1 Format (MJPEG) ---> (X) MJPEG ``` ##### H.264 ``` component config ---> USB Device UVC ---> USB Cam1 Config ---> UVC Cam1 Format (H264) ---> (X) H264 ``` ***Please note that the OV2640 doesn't support H.264 format, it only supports the JPEG format***. ### Build and Flash Build the project and flash it to the board, then run monitor tool to view serial output: ``` idf.py set-target esp32p4 idf.py -p PORT flash monitor ``` (To exit the serial monitor, type ``Ctrl-]``.) See the [ESP-IDF Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/esp32p4/get-started/index.html) for full steps to configure and use ESP-IDF to build projects. ## Example Output Running this example, you will see the following log output on the serial monitor: #### MIPI-CSI Development Kit ``` ... I (1641) main_task: Calling app_main() I (1641) gpio: GPIO[22]| InputEn: 1| OutputEn: 1| OpenDrain: 1| Pullup: 1| Pulldown: 0| Intr:0 I (1651) gpio: GPIO[23]| InputEn: 1| OutputEn: 1| OpenDrain: 1| Pullup: 1| Pulldown: 0| Intr:0 I (1661) sc2336: Detected Camera sensor PID=0xcb3a I (1741) example: version: 0.5.1 I (1741) example: driver: MIPI-CSI I (1741) example: card: MIPI-CSI I (1741) example: bus: esp32p4:MIPI-CSI I (1741) example: capabilities: I (1751) example: VIDEO_CAPTURE I (1751) example: STREAMING I (1761) example: device capabilities: I (1761) example: VIDEO_CAPTURE I (1761) example: STREAMING I (1771) example: version: 0.5.1 I (1771) example: driver: H.264 I (1781) example: card: H.264 I (1781) example: bus: esp32p4:H.264 I (1781) example: capabilities: I (1791) example: STREAMING I (1791) example: device capabilities: I (1801) example: STREAMING I (1801) example: Format List I (1801) example: Format(1) = H.264 I (1811) example: Frame List I (1811) example: Frame(1) = 1280 * 720 @30fps I (1821) usbd_uvc: UVC Device Start, Version: 1.1.0 I (1821) main_task: Returned from app_main() I (2031) usbd_uvc: Mount I (3281) usbd_uvc: Suspend ... ``` #### DVP Development Kit ``` ... I (1164) main_task: Calling app_main() I (1164) gpio: GPIO[32]| InputEn: 1| OutputEn: 1| OpenDrain: 1| Pullup: 1| Pulldown: 0| Intr:0 I (1174) gpio: GPIO[33]| InputEn: 1| OutputEn: 1| OpenDrain: 1| Pullup: 1| Pulldown: 0| Intr:0 I (1194) ov2640: Detected Camera sensor PID=0x26 I (1274) example: version: 0.5.1 I (1274) example: driver: DVP I (1274) example: card: DVP I (1274) example: bus: esp32p4:DVP I (1274) example: capabilities: I (1284) example: VIDEO_CAPTURE I (1284) example: STREAMING I (1284) example: device capabilities: I (1294) example: VIDEO_CAPTURE I (1294) example: STREAMING I (1304) example: version: 0.5.1 I (1304) example: driver: JPEG I (1304) example: card: JPEG I (1314) example: bus: esp32p4:JPEG I (1314) example: capabilities: I (1314) example: STREAMING I (1324) example: device capabilities: I (1324) example: STREAMING I (1334) example: Format List I (1334) example: Format(1) = MJPEG I (1334) example: Frame List I (1344) example: Frame(1) = 640 * 480 @6fps I (1344) usbd_uvc: UVC Device Start, Version: 1.1.0 I (1354) main_task: Returned from app_main() I (1564) usbd_uvc: Mount I (2824) usbd_uvc: Suspend ... ``` Open potplay APP and select follow option in menu: ``` PotPlayer --> Open --> Camera/Other Device ``` You can see following log on the serial monitor and video in potlayer display window: ``` I (192121) usbd_uvc: Resume I (192411) usbd_uvc: bFrameIndex: 1 I (192411) usbd_uvc: dwFrameInterval: 333333 ``` ## Troubleshooting * If the console log shows as follows, it means your ESP32-P4 chip version is v0.0, and it is not supported by default configuration, please configure the right version by menuconfig: ```txt A fatal error occurred: bootloader/bootloader.bin requires chip revision in range [v0.1 - v0.99] (this chip is revision v0.0). Use --force to flash anyway ``` menuconfig: ``` Component config ---> Hardware Settings ---> Chip revision ---> Minimum Supported ESP32-P4 Revision (Rev v0.1) ---> (X) Rev v0.0 ```