espressif/esp-brookesia - 0.5.0 - Example phone_s3_box

# ESP32-S3-BOX-3 运行 ESP-Brookesia Phone 示例 [English Version](./README.md) 这个示例演示了如何在 [ESP32-S3-BOX-3](https://github.com/espressif/esp-box/tree/master) 开发板上运行 ESP-Brookesia Phone，并使用 `320 x 240` 分辨率的 UI 样式表。 ## 入门指南 ### 硬件要求 * 一个 ESP32-S3-BOX-3 开发板。 ### ESP-IDF 要求 - 此示例支持 IDF release/v5.1 及更高的分支。默认情况下，它在 IDF release/v5.1 上运行。 - 请按照 [ESP-IDF 编程指南](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/esp32/get-started/index.html) 设置开发环境。**我们强烈建议**您 [构建第一个项目](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/esp32/get-started/index.html#build-your-first-project)，以熟悉 ESP-IDF 并确保环境设置正确。 ### 获取 esp-brookesia 仓库要从 esp-brookesia 示例开始，请在终端运行以下命令，将仓库克隆到本地电脑： ``` git clone --recursive https://github.com/espressif/esp-brookesia.git ``` ### 配置运行 ``idf.py menuconfig`` 并修改 esp-brookesia 配置。 ## 如何使用示例 ### 构建和烧录示例构建项目并将其烧录到开发板，然后运行监视工具查看串行输出（将 `PORT` 替换为您的开发板串口名称）： ```c idf.py -p PORT flash monitor ``` 要退出串行监视器，请输入 ``Ctrl-]``。完整的配置和使用 ESP-IDF 构建项目的步骤，请参见 [ESP-IDF 入门指南](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/get-started/index.html)。 ### 示例输出 - 完整日志如下： ```bash I (18) boot: ESP-IDF v5.5-dev-3644-g28ac0243bb 2nd stage bootloader I (19) boot: compile time May 30 2025 16:47:16 I (19) boot: Multicore bootloader I (19) boot: chip revision: v0.2 I (19) boot: efuse block revision: v1.3 I (20) qio_mode: Enabling QIO for flash chip GD I (20) boot.esp32s3: Boot SPI Speed : 80MHz I (20) boot.esp32s3: SPI Mode : QIO I (20) boot.esp32s3: SPI Flash Size : 16MB I (21) boot: Enabling RNG early entropy source... I (21) boot: Partition Table: I (21) boot: ## Label Usage Type ST Offset Length I (21) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (22) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (22) boot: 2 factory factory app 00 00 00010000 00400000 I (23) boot: End of partition table I (23) esp_image: segment 0: paddr=00010020 vaddr=3c080020 size=1c5f04h (1859332) map I (299) esp_image: segment 1: paddr=001d5f2c vaddr=3fca6800 size=031d0h ( 12752) load I (302) esp_image: segment 2: paddr=001d9104 vaddr=40374000 size=06f14h ( 28436) load I (308) esp_image: segment 3: paddr=001e0020 vaddr=42000020 size=76e50h (486992) map I (381) esp_image: segment 4: paddr=00256e78 vaddr=4037af14 size=1b894h (112788) load I (402) esp_image: segment 5: paddr=00272714 vaddr=600fe000 size=00020h ( 32) load I (415) boot: Loaded app from partition at offset 0x10000 I (416) boot: Disabling RNG early entropy source... I (416) octal_psram: vendor id : 0x0d (AP) I (417) octal_psram: dev id : 0x03 (generation 4) I (417) octal_psram: density : 0x05 (128 Mbit) I (417) octal_psram: good-die : 0x01 (Pass) I (417) octal_psram: Latency : 0x01 (Fixed) I (418) octal_psram: VCC : 0x00 (1.8V) I (418) octal_psram: SRF : 0x01 (Fast Refresh) I (418) octal_psram: BurstType : 0x01 (Hybrid Wrap) I (418) octal_psram: BurstLen : 0x01 (32 Byte) I (419) octal_psram: Readlatency : 0x02 (10 cycles@Fixed) I (419) octal_psram: DriveStrength: 0x00 (1/1) I (420) MSPI Timing: PSRAM timing tuning index: 6 I (420) esp_psram: Found 16MB PSRAM device I (420) esp_psram: Speed: 80MHz I (557) mmu_psram: Read only data copied and mapped to SPIRAM I (597) mmu_psram: Instructions copied and mapped to SPIRAM I (597) cpu_start: Multicore app I (1293) esp_psram: SPI SRAM memory test OK I (1301) cpu_start: Pro cpu start user code I (1301) cpu_start: cpu freq: 240000000 Hz I (1301) app_init: Application information: I (1302) app_init: Project name: phone_s3_box_3 I (1302) app_init: App version: v0.4.2-17-gdca3bd4-dirty I (1302) app_init: Compile time: May 30 2025 16:47:01 I (1302) app_init: ELF file SHA256: 3513ade3e... I (1302) app_init: ESP-IDF: v5.5-dev-3644-g28ac0243bb I (1303) efuse_init: Min chip rev: v0.0 I (1303) efuse_init: Max chip rev: v0.99 I (1303) efuse_init: Chip rev: v0.2 I (1303) heap_init: Initializing. RAM available for dynamic allocation: I (1304) heap_init: At 3FCAA908 len 0003EE08 (251 KiB): RAM I (1304) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM I (1304) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM I (1305) heap_init: At 600FE020 len 00001FC8 (7 KiB): RTCRAM I (1305) esp_psram: Adding pool of 14016K of PSRAM memory to heap allocator I (1305) esp_psram: Adding pool of 40K of PSRAM memory gap generated due to end address alignment of drom to the heap allocator I (1306) spi_flash: detected chip: gd I (1306) spi_flash: flash io: qio I (1307) sleep_gpio: Configure to isolate all GPIO pins in sleep state I (1307) sleep_gpio: Enable automatic switching of GPIO sleep configuration I (1308) main_task: Started on CPU0 I (1309) esp_psram: Reserving pool of 4K of internal memory for DMA/internal allocations I (1309) main_task: Calling app_main() I (1310) LVGL: Starting LVGL task W (1310) ledc: GPIO 47 is not usable, maybe conflict with others W (1310) i2c.master: Please check pull-up resistances whether be connected properly. Otherwise unexpected behavior would happen. For more detailed information, please read docs I (1311) ili9341: LCD panel create success, version: 1.2.0 W (1432) ili9341: The 36h command has been used and will be overwritten by external initialization sequence W (1432) ili9341: The 3Ah command has been used and will be overwritten by external initialization sequence I (1464) GT911: I2C address initialization procedure skipped - using default GT9xx setup I (1465) GT911: TouchPad_ID:0x39,0x31,0x31 I (1465) GT911: TouchPad_Config_Version:65 I (1465) ESP-BOX-3: Setting LCD backlight: 100% I (1465) app_main: Display ESP-Brookesia phone demo I (1466) app_main: Using stylesheet (320x240 Drak) [I][Brookesia][esp_brookesia_core.cpp:0213](beginCore): Library version: 0.5.0 I (1601) app_main: Biggest / Free / Total SRAM : [ 131072 / 181731 / 324851] PSRAM : [14155776 / 14388488 / 14393564] ``` - 以下动画展示了示例在开发板上运行的效果。 <p align="center"> <img src="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_box_3.gif" alt ="phone_s3_box_3" width="500"> </p> <p align="center"> （<a href="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_box_3.mp4">点击查看视频</a>） </p> ## 技术支持和反馈请使用以下反馈渠道： - 有技术问题，请访问 [esp32.com](https://esp32.com/viewforum.php?f=35) 论坛。 - 如需提交功能请求或错误报告，请创建 [GitHub issue](https://github.com/espressif/esp-brookesia/issues)。我们会尽快回复您。