espressif/esp-brookesia - 0.5.0 - Example phone_s3_lcd_ev

# ESP32-S3-LCD-EV-Board 运行 ESP-Brookesia Phone 示例 [English Version](./README.md) 这个示例演示了如何在 [ESP32-S3-LCD-EV-Board](https://docs.espressif.com/projects/esp-dev-kits/zh_CN/latest/esp32s3/esp32-s3-lcd-ev-board/index.html) 开发板上运行 ESP-Brookesia Phone，并使用 `480 x 480` 和 `800 x 480` 分辨率的 UI 样式表。 ## 入门指南 ### 硬件要求 * 一个配有 `480 x 480` 或 `800 x 480` 分辨率 LCD 屏幕的 ESP32-S3-LCD-EV-Board 开发板。 ### ESP-IDF 要求 - 此示例支持 IDF release/v5.1 及更高的分支。默认情况下，它在 IDF release/v5.1 上运行。 - 请按照 [ESP-IDF 编程指南](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/esp32/get-started/index.html) 设置开发环境。**我们强烈建议**您 [构建第一个项目](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/esp32/get-started/index.html#build-your-first-project)，以熟悉 ESP-IDF 并确保环境设置正确。 ### 获取 esp-brookesia 仓库要从 esp-brookesia 示例开始，请在终端运行以下命令，将仓库克隆到本地电脑： ``` git clone --recursive https://github.com/espressif/esp-brookesia.git ``` ### 配置运行 ``idf.py menuconfig`` 并修改 esp-brookesia 配置。 ## 如何使用示例 ### 构建和烧录示例构建项目并将其烧录到开发板，然后运行监视工具查看串行输出（将 `PORT` 替换为您的开发板串口名称）： ```c idf.py -p PORT flash monitor ``` 要退出串行监视器，请输入 ``Ctrl-]``。完整的配置和使用 ESP-IDF 构建项目的步骤，请参见 [ESP-IDF 入门指南](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/get-started/index.html)。 ### 示例输出 - 完整日志如下： ```bash I (25) boot: ESP-IDF v5.5-dev-3644-g28ac0243bb 2nd stage bootloader I (25) boot: compile time May 30 2025 16:54:03 I (25) boot: Multicore bootloader I (25) boot: chip revision: v0.2 I (25) boot: efuse block revision: v1.3 I (25) qio_mode: Enabling QIO for flash chip GD I (26) boot.esp32s3: Boot SPI Speed : 80MHz I (26) boot.esp32s3: SPI Mode : QIO I (26) boot.esp32s3: SPI Flash Size : 16MB I (26) boot: Enabling RNG early entropy source... I (26) boot: Partition Table: I (26) boot: ## Label Usage Type ST Offset Length I (27) boot: 0 nvs WiFi data 01 02 00009000 00006000 I (27) boot: 1 phy_init RF data 01 01 0000f000 00001000 I (28) boot: 2 factory factory app 00 00 00010000 00400000 I (28) boot: End of partition table I (28) esp_image: segment 0: paddr=00010020 vaddr=3c080020 size=2542e0h (2441952) map I (391) esp_image: segment 1: paddr=00264308 vaddr=3fca4d00 size=03530h ( 13616) load I (394) esp_image: segment 2: paddr=00267840 vaddr=40374000 size=087d8h ( 34776) load I (401) esp_image: segment 3: paddr=00270020 vaddr=42000020 size=776b4h (489140) map I (473) esp_image: segment 4: paddr=002e76dc vaddr=4037c7d8 size=184b8h ( 99512) load I (493) esp_image: segment 5: paddr=002ffb9c vaddr=600fe000 size=00020h ( 32) load I (505) boot: Loaded app from partition at offset 0x10000 I (505) boot: Disabling RNG early entropy source... I (506) octal_psram: vendor id : 0x0d (AP) I (506) octal_psram: dev id : 0x03 (generation 4) I (506) octal_psram: density : 0x05 (128 Mbit) I (506) octal_psram: good-die : 0x01 (Pass) I (507) octal_psram: Latency : 0x01 (Fixed) I (507) octal_psram: VCC : 0x00 (1.8V) I (507) octal_psram: SRF : 0x01 (Fast Refresh) I (507) octal_psram: BurstType : 0x01 (Hybrid Wrap) I (507) octal_psram: BurstLen : 0x01 (32 Byte) I (508) octal_psram: Readlatency : 0x02 (10 cycles@Fixed) I (508) octal_psram: DriveStrength: 0x00 (1/1) I (509) MSPI Timing: PSRAM timing tuning index: 6 I (509) esp_psram: Found 16MB PSRAM device I (509) esp_psram: Speed: 80MHz I (688) mmu_psram: Read only data copied and mapped to SPIRAM I (728) mmu_psram: Instructions copied and mapped to SPIRAM I (729) cpu_start: Multicore app I (1396) esp_psram: SPI SRAM memory test OK I (1405) cpu_start: Pro cpu start user code I (1405) cpu_start: cpu freq: 240000000 Hz I (1405) app_init: Application information: I (1405) app_init: Project name: phone_s3_lcd_ev_board I (1406) app_init: App version: v0.4.2-17-g9a34de7 I (1406) app_init: Compile time: May 30 2025 16:53:48 I (1406) app_init: ELF file SHA256: b2cc97278... I (1406) app_init: ESP-IDF: v5.5-dev-3644-g28ac0243bb I (1407) efuse_init: Min chip rev: v0.0 I (1407) efuse_init: Max chip rev: v0.99 I (1407) efuse_init: Chip rev: v0.2 I (1407) heap_init: Initializing. RAM available for dynamic allocation: I (1408) heap_init: At 3FCA9110 len 00040600 (257 KiB): RAM I (1408) heap_init: At 3FCE9710 len 00005724 (21 KiB): RAM I (1408) heap_init: At 3FCF0000 len 00008000 (32 KiB): DRAM I (1409) heap_init: At 600FE020 len 00001FC8 (7 KiB): RTCRAM I (1409) esp_psram: Adding pool of 13440K of PSRAM memory to heap allocator I (1409) esp_psram: Adding pool of 47K of PSRAM memory gap generated due to end address alignment of drom to the heap allocator I (1410) spi_flash: detected chip: gd I (1410) spi_flash: flash io: qio I (1411) sleep_gpio: Configure to isolate all GPIO pins in sleep state I (1411) sleep_gpio: Enable automatic switching of GPIO sleep configuration I (1412) main_task: Started on CPU0 I (1460) esp_psram: Reserving pool of 32K of internal memory for DMA/internal allocations I (1460) main_task: Calling app_main() I (1461) LVGL: Starting LVGL task I (1461) bsp_probe: Detect module with 16MB PSRAM W (1461) i2c.master: Please check pull-up resistances whether be connected properly. Otherwise unexpected behavior would happen. For more detailed information, please read docs I (1462) bsp_probe: Detect sub_board3 with 800x480 LCD (ST7262), Touch (GT1151) I (1462) bsp_sub_board: Initialize RGB panel I (1569) gt1151: IC version: GT1158_000101(Patch)_0102(Mask)_00(SensorID) I (1570) app_main: Display ESP-Brookesia phone demo I (1570) app_main: Using stylesheet (800x480 Dark) [I][Brookesia][esp_brookesia_core.cpp:0213](beginCore): Library version: 0.5.0 I (1802) app_main: Biggest / Free / Total SRAM : [ 176128 / 251603 / 359659] PSRAM : [12582912 / 12874240 / 13810944] ``` - 以下动画展示了示例在不同开发板上运行的效果。 <img src="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_480_480.gif" alt ="phone_s3_lcd_ev_board_480_480" width="400"> ESP32-S3-LCD-EV-Board（带有 480 x 480 分辨率的 LCD 屏幕）（<a href="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_480_480.mp4">Click to view the video</a>） <img src="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_800_480.gif" alt ="phone_s3_lcd_ev_board_800_480" width="400"> ESP32-S3-LCD-EV-Board-2（带有 800 x 480 分辨率的 LCD 屏幕）（<a href="https://dl.espressif.com/AE/esp-dev-kits/esp_ui_phone_s3_lcd_ev_board_800_480.mp4">Click to view the video</a>） ## 技术支持和反馈请使用以下反馈渠道： - 有技术问题，请访问 [esp32.com](https://esp32.com/viewforum.php?f=35) 论坛。 - 如需提交功能请求或错误报告，请创建 [GitHub issue](https://github.com/espressif/esp-brookesia/issues)。我们会尽快回复您。