uploaded 1 month ago
ESP-Hosted-MCU provide drivers to act any ESP chipset as Wi-Fi or Bluetooth co-processor.
-
host_bluedroid_ble_compatibility_test
This example tests Bluetooth compatibility and mobile phone interactions using the ESP32-P4 Dev Board as the BT Host connected to an ESP32 co-…
Archive size ~ 12.51 KB
-
host_bluedroid_bt_hid_mouse_device
This example demonstrates the implementation of a Bluetooth HID device using the Classic Bluetooth HID profile APIs. It simulates a Bluetooth HID…
Archive size ~ 10.70 KB
-
host_bluedroid_host_only
This example demonstrates how to use the ESP-Hosted as a Bluetooth Host via HCI IO to the BT Controller, enabling ESP32-P4 Dev Board to communicate…
Archive size ~ 6.14 KB
-
host_bt_controller_mac_addr
This example shows how to change the MAC Address for the BLE Scanner, allowing a device named `Bluedroid_Beacon` to appear with the assigned MAC…
Archive size ~ 7.47 KB
-
host_gpio_expander
This example demonstrates how to use the ESP-Hosted solution to control the GPIOs of the slave (co-processor) from the host MCU. It provides…
Archive size ~ 2.89 KB
-
host_hosted_events
This example demonstrates the use of ESP-Hosted events to detect when a co-processor resets or hangs, allowing for automatic reinitialization of the…
Archive size ~ 11.69 KB
-
host_network_split__power_save
This example demonstrates the integration of **Network Split** and **Host Deep Sleep** features on ESP-Hosted devices. It allows the host MCU to…
Archive size ~ 17.43 KB
-
host_nimble_bleprph_host_only_uart_hci
This BLE Peripheral Example outlines how to implement a custom UART transport for ESP32 devices. It details project configuration steps for both the…
Archive size ~ 501.02 KB
-
host_nimble_bleprph_host_only_vhci
This example demonstrates the use of the Bluetooth Hosted HCI transport provided by ESP-Hosted. It requires specific configuration where the…
Archive size ~ 13.26 KB
-
host_peer_data_transfer
This example demonstrates how to send and receive raw binary data between a host device and a coprocessor, allowing for maximum control over data…
Archive size ~ 5.72 KB
-
host_performs_slave_ota
This example demonstrates ESP-Hosted Transport OTA, allowing firmware updates for a slave device through an existing ESP-Hosted connection…
Archive size ~ 36.98 KB
-
host_sdcard_with_hosted
This example demonstrates how to use an SD card on an ESP32-P4 board while ESP-Hosted communicates with the ESP32-C6 via SDIO. It initializes ESP-…
Archive size ~ 12.44 KB
-
host_shuts_down_slave_to_power_save
This example demonstrates host-side control of an ESP slave to reduce power consumption by shutting the slave down when idle and waking it up on…
Archive size ~ 7.28 KB
-
host_transport_config
This example demonstrates how to configure ESP-Hosted transport interfaces (SDIO, SPI, UART) before initialization, showcasing the default transport…
Archive size ~ 6.63 KB
-
host_wifi_easy_connect_dpp_enrollee
This example demonstrates how to configure ESP devices as an enrollee using the Device Provisioning Protocol (DPP), also known as Wi-Fi Easy Connect.…
Archive size ~ 6.26 KB
-
host_wifi_itwt
This example shows how to use itwt (Immediate-Traffic Wi-Fi Target) of Wi-Fi, which only works in station mode and requires the AP to support it.…
Archive size ~ 14.98 KB
-
slave
The ESP-Hosted MCU Slave Example demonstrates firmware that enables host MCUs to access Wi-Fi and Bluetooth through ESP32 co-processors using SDIO,…
Archive size ~ 466.56 KB